When you buy a new hoverboard, you can't wait to ride it. But when you turn on it and find that the hoverboard keeps beeping, you may feel a little disappointed. Or maybe you have been riding the hoverboard for a while and suddenly it won't stop beeping.
If you feel that you have tried everything and can't stop, this problem can be a bit annoying to very frustrating and make you go crazy. Well, don't worry, because below you will find common fixes to turn off the beep and restore peace.
Here we have collected some beeping situations and provided some simple solutions for you.
Why Does The Hoverboard Beeps When Turned On
Most hoverboards have indicator lights and alarm systems designed to signal you that you may not be on a safe surface or that the battery is low. These built-in safety features are designed to prevent situations where the hoverboard may not work properly, which may increase the risk of damage or injury.
3 Reasons Why Your Hoverboard Beeps And Flash Light When Ridding
1. Uneven Surface - Keep Beeping
Sometimes the smart balance wheel will not stop beeping because the surface is not correct and it is tilted forward or backward more than 15 degrees. It may also be because the self-balancing scooter is sitting on a slope of more than 30 degrees. Solve this problem by moving to a flat, smooth surface.
2. Speed Too Fast - Keep Beeping
If you exceed the maximum speed of the hoverboard, riding a skateboard becomes very dangerous. This is why they have a safety function, which is triggered by a speed that exceeds the maximum speed. The circuit board will start to slow down and a beep will warn you that the speed is too fast.
Another method is to adjust the maximum travel speed of the hoverboard. Such as changing from child mode to adult mode.
3. Low Battery - Keep Beeping And Red Light
When the battery level of your hoverboard drops below 20%, the green light will start to flash. If the red light flashes, it means that your battery's lifespan is severely low and you need to charge it immediately. If you see any of these lights, stop riding the hoverboard and charge it as usual.
How To Fix Hoverboard Beeping While Charging
If the green light on hoverboard blinks, it means your battery level is lower than 20%, if the red light starts beeping, this indicates your battery level is extremely low, which less than 5%, be careful not to ride under this situation, in both cases, you just need to charge your hoverboard in a normal way.
How To Fix The Hoverboard Beeps And Won't Turn Off
- If the hoverboard keeps beeping and does not turn off, you should place the hoverboard in the backyard or garage to allow the skateboard to drain the battery. This may take a while. When the battery power is zero, the hoverboard will automatically shut down. Now all you need to do is use the charger and wall socket to charge the hoverboard for 2-3 hours. After the hoverboard is fully charged, turn on the power switch and you will find that the hoverboard is working normally.
- If the first method does not produce the expected result, the motherboard of your hoverboard may be defective. You can use a hoverboard repair kit to solve this problem, you can buy the kit online, or you can pay for the repair service on the board to solve this problem.
5 Most Useful Ways To Stop Hoverboard From Beeping
If you are not sure what caused the beeping, or there is no obvious solution, here are some common ways to stop your hoverboard beeping.
Way 1 - How To Calibrate A Beeping Hoverboard
- Step 1: To calibrate, please close the hoverboard first.
- Step 2: Adjust the foot pedal until it is flush with the ground.
- Step 3: Press and hold the power button for 10 seconds. Another beep will sound and the LED light will flash.
- Step 4: Press the power button to shut down.
- Step 5: Press the power button to turn on. The hoverboard will be calibrated and ready, you can try it out.
Note: You may need to repeat the above process several times to completely reset and calibrate your hoverboard, but it is best not to exceed 5 times in a row.
Way 2 - Reconnect Loose Wires
- Similarly, the first step is to turn off the device.
- The next step is to unscrew the small screws scattered on the self-balancing scooter.
- Turn it on slowly, and you will see the power cord and the hall cord.
- Now, you need to check two things, the first is whether the wires are loose, and the second is whether the wires are not clamped in.
- If it is a problem that the wires are cut, it can be solved by pulling them out and then pushing them back.
- If the wire is loose, you need to disconnect it, push the clip outward a little with a pen/pencil, and then reconnect it.
- In both cases, a little sound will let you know if you are doing it right.
- In both cases, you must also connect the wires correctly by matching the color of the wires.
- Fix the hoverboard again, tighten the screws and power on.
Way 3 - Trouble Shot with Different Flashing Numbers
|
Flash 1 Times |
There is a problem with the motherboard. Disconnect and reconnect all connections on the motherboard. If this does not solve the problem, please consider replacing the motherboard |
|
2 or 3 Times |
There is an internal circuit problem. Purchase a circuit board replacement kit and follow the instructions |
|
4 or 5 Times |
There is an internal motor problem. 4 flashes indicate a problem with the motor on the main board side of the device, and 5 flashes indicate a problem with the motor on the battery side. You may need to replace the faulty motor |
|
Flash 6 Times |
There is a problem with the battery. In this case, you may need to replace the battery |
|
7 or 8 Times |
There is a problem with the gyroscope. This can range from pin deviations to unstable sockets to poor interface alignment. You can replace the gyroscope or the entire circuit board to solve the problem |
|
Flash 9 Times |
There is a problem with the direction. In short, your hoverboard is turned on when it is upside down, in this case all you need to do is to turn the device face up to stop beeping |
Way 4 - Contact the Supplier for Return or Exchange.
If the hoverboard has this beeps issue and it is still within the warranty period, please contact your supplier customer service and ask them to help you.
Way 5 - Send to a Repair Shop Near You
If your hoverboard has passed the warranty period, you can only repair it yourself or send it to a nearby repair shop. Generally, replacing to a new motherboard can solve the beeping problem.
After reading this article, I hope these can help you.
If you are considering buying a new hoverboard, you can choose Gyroor hoverboard, UL2272 certification, one-year warranty for the product, and 6-month warranty for the battery.
Related: